Skip to content
Home » How To Fix Directv That Is Searching For A Satellite Signal

How To Fix Directv That Is Searching For A Satellite Signal

Locate your Access Card behind a small front panel on your DirecTV receiver/box. Remove then re-insert your access card and wait 30 seconds. If this fixes the problem, you most likely still have an issue either with this satellite dish or the cables that run from the dish to your receiver.Dec 30, 2020

Why does my DIRECTV say searching for satellite?

The receiver is searching because the dish is out of alignment.

Why is my DIRECTV not getting a signal?

A broken coaxial cable, HDMI or an ethernet cable can also cause a TV signal loss. If you have a spare cable, try replacing the existing cable and check for the signal. This solution even works for problems like the DIRECTV Genie not working in one room and the DIRECTV Network Connection Not Found error.

How do I get my satellite signal back?

Unplug the receiver from your electrical power outlet. Leave it unplugged for 30 seconds and plug it back in. Allow the receiver to restart and re-acquire the signal.

Why does my satellite Say no signal?

Signal Loss Error Message

This issue is usually a result of the satellite dish being in a slightly wrong position, damaged or malfunctioning equipment, severe weather, or something blocking the dish’s view of the sky.

Why can’t I get a satellite signal?

Check all the cables between your TV equipment and satellite dish are connected securely. Try disconnecting and reconnecting the cables as this often works. While doing so, check none are damaged or wet. Unplug your receiver from the mains and leave for 10 minutes.

Why is my DIRECTV saying waiting for receiver signal?

On some DIRECTV receivers there is a red reset button located inside the access card door on the front panel. Press the button and wait for your receiver to reboot. If you cannot locate the red reset button or your receiver does not have one: Unplug the receiver’s power cord from the electrical outlet.

How can I check if my satellite dish is working?

There is a chance that your satellite dish is working perfectly fine. You can check this by disconnecting the satellite receiver and plugging in a spare/new one or by checking the signal on other TV sets in the home.

What does 775 mean on DIRECTV?

You’ll see DIRECTV error code 775 when the signal between your receiver and satellite dish is interrupted. Check your receiver connections to resolve this issue.

Where is the reset button on my DIRECTV receiver?

Method 1: Press the reset button

On most DIRECTV receivers, there is a small red button located inside the access card door. With others, the button is on the side of the receiver. Press the red button, then wait for your receiver to reboot.

How do I reset my satellite dish?

Reset your DISH receiver

Unplug the power cord of your DISH receiver (typically has a red tag) from the electrical outlet for 10 seconds, then plug it back in. If you have a Hopper & Joey system, unplug the power cord of the Hopper (the main, large receiver). The reset process may take up to 5 minutes to complete.

What does 771 mean on Direct TV?

If you see error code 771, it means your DIRECTV receiver is having trouble communicating with your satellite dish.

What can interfere with a satellite signal?

Scaffolding, buildings, walls and even trees blocking the path to the satellite may cause interference. Bad weather – heavy rain can affect your satellite television reception. If high winds cause problems then the dish may not be securely fixed.

Can a satellite dish be faulty?

Look at your satellite dish to see if it may have been knocked out of position by a heavy wind or a falling object. If the dish seems to be out of position but not broken, call your satellite company to have it aligned. If it is bent or the feed horn is bent or broken, the dish is bad.

How do I align my satellite dish?

The first step to setting up your dish is to point the dish in a South to Southeast direction, this can be achieved either using the position of the sun or using a compass (B2022). Although the orbital position of the satellite is 28.2 degrees East of South, the actual compass bearing will be slightly different.

What does refresh your receiver mean?

You’re really re-downloading the software stream. It seems like your receiver gets a refresh, and like it acts better than before. It does take a few minutes. It’s just not a direct, push-button kind of thing.

How can I tell if my LNB is faulty?

LNBs can degrade over time, particularly in locations exposed to extreme weather conditions; signs of a faulty LNB include missing channels, video pixilation, signal drop-out during heavy rain or a complete loss of signal.

How do I reset my DIRECTV 775?

Unplug the Swim power inserter from the power outlet. Wait for 30 seconds. Plug the Swim power inserter back into its power outlet, and make sure it’s turned on and working. Make sure everything’s hooked up, turn your TV on and check to see if the issue has been resolved.

How do I reset my DIRECTV 782?

If you’ve recently moved your receiver to a different location in your home, this can result in a 782 error. To clear the error, move the receiver back to its original location and turn it on.

What is error code 782 on DIRECTV?

You’ll see DIRECTV error code 782 when the signal between your receiver and satellite dish is interrupted.

How do I fix 771?

Locate your Access Card behind a small front panel on your DirecTV receiver/box. Remove then re-insert your access card and wait 30 seconds. If this fixes the problem, you most likely still have an issue either with this satellite dish or the cables that run from the dish to your receiver.

What does 711 mean on DIRECTV?

DIRECTV error code 711 indicates that your receiver may need to be activated, or your service refreshed.

Can satellite signal be blocked?

The satellite dish needs “line of sight” of the satellites in space. This means that nothing can be blocking the signal between the satellite and satellite dish or you will have poor satellite TV reception. The higher frequencies and shorter wavelength means more of the signal is absorbed into the trees and leaves.

Can I spray Pam on my satellite dish?

Non-stick cooking and waterproofing sprays such as PAM or Rain-X are not recommended for keeping snow and ice off your satellite dish. These sprays can actually make it more likely to accumulate dirt and pollen, which then creates an ideal surface for snow and ice to accumulate.

How do you stop signal interference?

Keep cables as short as possible, and pay attention to routing. A long cable not only increases power line common-impedance coupling (for unbalanced cables), but it also makes the cable a better antenna. Routing cables close to such ground planes as metal racks or concrete floors will reduce antenna effects.

How long does a TV satellite dish last?

On average, you can expect about ten years of life from a quality satellite dish. Because the dish is outside of your home, it takes a beating whenever there is extreme weather in your area, which can shorten its life.

What does LNB drift detected mean?

An LNB Drift indicates that the LNB’s internal oscillator frequency is operating out of normal range, and therefore, it could not compensate for any normal fluctuations with the incoming satellite signal. This explains my signal quality issues; the LNB hardware is failing.

How do I align my dish satellite without a meter?

To find satellite signal without a meter, you need to rotate your dish for horizontal adjustment, followed by vertical adjustment for the elevation. Work with a partner who can monitor the changes in signal strength from the television.

Is there an app to find satellite signal?

SatFinder (Satellite Finder) is a tool which will help you to set up satellite dish. It will give you azimuth, elevation and LNB tilt for your location (based on GPS) and chosen satellite from list. The result is shown both as numeric data and graphical on google maps.