Skip to content
Home » How To Hook Up A Dvd Player To A Television That Has A Satellite Dish

How To Hook Up A Dvd Player To A Television That Has A Satellite Dish

The simplest way to connect a television with a DVD player and a satellite receiver is to attach both devices directly to the TV’s audio/video jacks using standard sets of composite cables with RCA-type plugs on the ends.

How do I use my DVD player with Dish Network?

Turn on the satellite box, TV set and DVD player (make sure they are all plugged in). Insert a DVD into the player. If all the appropriate connections are made, the satellite TV signal should broadcast on the TV set and the DVD video should appear when the disc is played.

How do I get my DVD player to work with DirecTV?

Power on your TV first, then turn on the Blu-ray player and the DirecTV HD DVR. Press the “Input” or “Source” button on the television remote control to set the video source to the DVR if required. Press the “Source” button on the DirecTV remote to set its video source to the port name you used on the Blu-ray player.

How do you hook up a DVD player to yellow red and white TV?

Newer DVD players typically come with an HDMI cable, which you can simply plug into the TV and DVD player. However, older models may come with a composite cable. To use this, connect the red, white and yellow plugs into their respective ports on both devices.

How do I connect my DVD player to my receiver and TV?

How do I connect my TV to Dish Network?

Connecting Your Satellite Dish to Your TV

Connect the other end of the coaxial cable to your satellite receiver in the port marked “Sat in”. Next, connect one end of the HDMI cable to the ‘output’ port in the back of the satellite. Plug the other end of the HDMI cable in to your TV (not your dish receiver).

How do I change the input on my DISH Hopper remote?

Save your setting. Then press the clear TV button at the very top of your remote. Then press Menu and it should pull up your tv menu. Then press the Input button and you should be in business.

How do I start my DVD player?

Press the “Eject” button on the DVD player (it will be shaped like a triangle over a horizontal bar) to open the disc tray. Put the DVD in the tray and close it either by pressing it in or pressing the eject button. The DVD will then begin playing.

What is the input channel for DirecTV?

The TV set only goes to a channel (3 or 4) if the Driectv box is connected like a traditional antenna. If your Directv box is connected by HDMI then you put your TV’s input on HDMI-1, HDMI-2, etc. depending which one it is plugged into.

Why isn’t my DVD player working on my TV?

Play a different DVD to determine whether or not the problem is being caused by the disc itself. NOTE: If the issue only occurs with the first DVD, then the disc may have dust, fingerprints or scratches. Ensure the TV and DVD player are set to utilize the same type of video signal, either progressive or interlaced .

Can you connect an old DVD player to a new TV?

If so, you can get yourself a component cable and connect the DVD player to the TV using those plugs. You can plug the RCA (yellow/red/white) output in to this box and connect the HDMI output from the box to your TV using an HDMI cable.

Why does my TV say no signal when I plug in my DVD player?

Change the INPUT or source the HDTV is set to by pressing the INPUT button on the TV or its original remote. When you try different inputs, let the DVD player play a disc and output a constant signal. 2. If your TV has the correct INPUT or Source, unplug the cable and plug it back, or try another cable or port.

Where do you plug red white and yellow cables?

Yellow is for video input, white is for left audio input (Mono), and red is for audio right side input. After you have inserted the cables and your Wii is powered, look for Input Select for your TV to view the game. You can find this by pressing the TV/Video button on the TV remote.

How do I connect my DVD player to my HDMI TV?

How do I hook up my DVD player to my cable box?

Attach your cable to your DVD player.

Plug the HDMI or s-video cable into the appropriately labeled port on the back of the DVD player. If you’re using an s-video cable, you’ll also need to plug the red and white RCA cables into the red and white ports on the back of the DVD player.

How do you connect two DVD players together?

You will need to purchase a 4-pole 3.5mm Jack to Jack lead to connect both DVD players together: Insert your DVD movie disc into one player and connect using its AV OUT socket to the second DVD Player using it’s AV IN socket.

Can you connect satellite to TV without the box?

Like we mentioned earlier, you cannot connect your satellite to a TV without a box. The satellite receiver for TV is what decodes and demodulates the signal so you can view your shows. Only TVs that have satellite support for demodulation can connect to a satellite without a TV receiver box.

Can you plug a satellite dish into a TV?

The short answer to this question is no. Because of the high frequencies they receive, it makes them incompatible for a TV to decode and display without some sort of device to lower the frequency to around 1GHz.

How do I connect a second TV to my satellite dish?

Though it technically is possible to connect a second TV to your current satellite receiver it may not be worthwhile to do so. In order to connect two TV’s to one satellite Receiver you would need to install an aftermarket multi-switch to your current receiver.

How do I change the input on my directv remote?

If you need to change the input on your TV while watching DIRECTV, or if you just don’t want to drag out the TV remote, press and hold the ENTER button (to the right of the zero) for about two seconds to bring up the menu to change your TV’s input.

What are HDMI ports?

High-Definition Multimedia Interface (HDMI) is a proprietary audio/video interface for transmitting uncompressed video data and compressed or uncompressed digital audio data from an HDMI-compliant source device, such as a display controller, to a compatible computer monitor, video projector, digital television, or …

How do I hook up my DIRECTV SWM?

Connect the incoming satellite dish coax cable to the Power Inserter’s “Power to SWM” connector. Connect the DVR/Receiver coax cable to the Power Inserter’s “Signal to IRD” connector. ACEs are customers too, NOT employees. Answers are based on experience. I strive to give honest answers, even if not always appreciated.

How do you program a DIRECTV remote to a TV that is not listed?

From the on-screen instructions, select Settings & Help > Settings > Remote Control > Program Remote. Choose the device (TV, audio, DVD, etc.) you want to program. If you don’t see your TV or device listed, use the DIRECTV code lookup tool to find the device’s five-digit code.

Why is my DIRECTV remote not working RC73?

To reset the RC73 remote: -Press and hold mute and select until the light blinks. -After releasing mute and select, type the numbers “9, 8, 1” in that order. -You should see the light blink again on the remote after typing the above 3 numbers.

Why won’t my DVD player recognize DVDs?

Use a soft cloth to clean the disc ; the disc may have fingerprints or smudges. Examine the disc for any cracks or scratches that might be interfering with playback. Make sure the disc playback is not restricted by parental control options. Make sure the DVD disc is compatible with the player.

Why is the TV saying no signal?

Overview. A “No Signal”, “No Source”, or “No Input” message will appear on your TV screen if the TV is not receiving a signal from your TV box. This is often a result of either the TV box being powered off, not being properly connected to the TV, or the TV being set to the wrong input.

How do you hook up a DVD player to a TV without HDMI?

If this side of the cable feature 1 SCART cable, connect it to the SCART OUT port of your device. If there’s a proprietary port, connect it to the corresponding port of your DVD player. Connect the white and red audio connectors to the AUDIO OUT ports of your DVD player.

What cable do I need to connect DVD player to TV?

HDMI Cable 1.8M High Speed to TV, DVD Player, Laptop, TV | Agagadgets.

Do you need an aerial for DVD player?

No, you don’t need to connect to a tv aerial to watch a DVD.

How do you hook up a DVD player to a Toshiba TV?

Insert one end of the yellow composite cable into the “Video Out” port on the rear of the TV and insert the other end into the yellow “Video In” port on the TV’s Input panel. Insert one end of the red cable to the red “Audio Out” port and plug the other end into the “Audio In” port on the TV.

How do I connect red white and yellow cables to my Samsung TV?

1) Using video/audio cables, connect the VIDEO (yellow) / AUDIO (red and white) OUT terminals on the rear of the Blu-ray Disc Player to the VIDEO (yellow) / AUDIO (red and white) in terminals of your TV.

How do you hook up a DVD player to a Yamaha receiver?

DVD Player Optical Connection Remove dust cap on optical input as shown on insets. Connect optical cable  to receiver. Connect optical cable to DVD player from receiver. DVD Player Video Connection Top: Connect RCA video cable  to receiver: Yellow to “DVD,” as shown, and leave White and Red unplugged.

Will a smart TV work with Dish Network?

While you can’t use the DISH Anywhere app for your smart TV, the DISH Network Hopper DVR puts the “smart” in any standard television—and makes your smart TV into a DISH smart TV. Plus, with professional installation, you can enjoy the best in-home entertainment without any hassle.